0-10V LED Dimmer Switch, Low Voltage Dimmer Switch for Dimmable LED Lights, CFL

  

10 pack white 0-10V low voltage LED dimmer switch, 5%-100% dimming ability, provide the best dimming performance for dimmable LED lights. For use with up to 150 Watts of dimmable LED/CFL and up to 600 Watts of Incandescent and Halogen lamps. Features a large rocker paddle to turn lights on/off or to preset level and a fluent slider to brighten/dim lights to suit different activities. The 0-10V LED dimmer switch can be used in single pole or 3-way applications.

Providing precise full-range dimming control. Easy to install and use. Single Pole & 3-way low voltage LED dimmer switch for LED lights, ONLY support LED/CFL and Incandescent lamps with 0-10V driver. We are specialized in UL standard 0-10V dimmer switch for LED lights, USB outlet, smart WiFi in-wall outlet products, our ability is not limited to marketing and manufacturing, but also R&D development. Every thing we sell comes from our own factory directly.

KEYGMA is an American electrical brand, all our products are protected by the Intellectual Property Laws. The KEYGMA 3-way 0-10V LED dimmer provides optimal dimming performance of LED bulbs. This dimmer switch works with up to 150 Watts of dimmable LED/CFL or 600 Watts of incandescent/ halogen, allowing you to control multiple bulb types on the same circuit.

It is designed to control a broad range of dimmable LED and CFL bulbs from a variety of brands including GE, Philips, EcoSmart, Cree, Lighting Science and others. The LED dimmer features a paddle switch to turn your lights off or on returning the lights to your favorite level. This dimmer also features a discreet slide control next to the switch, allowing you to adjust the lights for any activities. Good Quality and Good Compatibility. Tested on thousands of bulbs and most brands to ensure.

KEYGMA 0-10V LED Dimmer Switch for LED Lights. Easily turn the lights on and off with a paddle switch, and use the fluent slide control to adjust the lights to the perfect level. It can be used for single-pole and three-way applications. 150W dimmable LED/CFL bulbs or 600W INC/HAL. Wide range of compatibility with sensitivity dial (At the bottom of back side of dimmer switch).

Support LED/CFL and Incandescent lamps with 0-10V driver. Meet UL standard, high quality. The dimming effect is very good. Includes instructions, wall plate(white), mounting screws and wire caps. 0-10V LED/CFL Dimmer Switch Installation Tips.

Install in accordance with all national and local Electrical Codes. Use copper power wires that are rated for least 75 Degrees Celsius/167 degrees Fahrenheit.

CUT OFF ALL THE POWER CIRCUIT before starting installation. Use the wiring diagram (see the user manual) to connect the dimmer switch between a 0-10V power supply and 0-10V LED light fixture. Always observe proper polarity when connecting power and load.

Shorting output wires may cause damage to dimmer. Carefully replace wiring back into wall box, mount the LED dimmer with supplied screws.

For indoor use only - the 0-10V dimmer switch is not waterproof or weatherproof. Smooth dimming of the broadest range of LED. Here're some tips (Trouble Shooting). Make sure all your bulbs/lamps or LED lights are.

Marked dimmable and with 0-10V Driver. Better not use one dimmer switch to control a group of lighting fixtures/lamps, it may cause flicker due to variation of dimming circuit and dimming range. Please slide the dimmer at high brightness level (recommended 50%), then turn on/off the dimmer switch, if your LED lights driver is too bad.

Bulbs may flicker or flash when dimmed to a low brightness level. If your lighting fixture is not compatible with our LED dimmer. Please change the dimmer switch or your lighting fixture.

Slightly slide the dimming slider to achieve full compatibility with the lights. If still buzzing, flicker or flash, please adjust the sensitivity dial slowly until the symptom is no longer present. (Better adjust it before install, the sensitivity dial is at the bottom of back side of the Dimmer Switch). Find a professional electrician to install the dimmer switch to avoid wiring error.